Material Safety Date Sheet

1、 Identification of the substance/preparation and company

 Product Information: white
 Product Number:W3001
 Information on Producer/Suppiler Name.Address.Phone:
 Guang ahou Bao Saheng polyurethanes Pigment Co.LTD,.
 0769-88188806 88187729
 Emergency Phone/Fax:     0769-88187719
2、 Composition/Information on Ingredients
 Singe:NO
 English Name:-
 Synonyms:-
 Chemical Abstracts Number(CAS NO):-
 Percentage for Chemical Ingredient(%):

  Mixing:
Chemical Characteristics:
Hazardous Components Name Concentrartion(%) Hazard symbols
Polyester Polyol Resin 82.2% N/A
Color Pigments 17.8% N/A

3.、Hazard Identification

Major Hazard Effect
  • Hazard Effect:
    Eye:May cause teardrops or irritation.
    Skin:May cause the itch or irritation.
    InhaIation:At room temperatuer,vapors are minimal and no obvious hazard,If heated, it may cause irritation of the eyes,upper respiratiry tract,and lungs by excessive exposure.
    Ingestion:No hazards are anticipated from ingestion incidental to industrial exposure.
Hazard Warnings for Environment:
Physical and Chemical Dangerous:
Special Harm:
major state:
Hazard Category:


4.First Aid Measures:
Emergency and First Aid Procedures:
Inhalation:Remove victim to fresh air.Give Oxygen or artificial respiration if necessary.
Skin contact:Remove contaminated clothing.Gently remove excess polymer from skin.Wash by soap or mild detergent with water. Then flush with large amount of water for at least 15~20 minutes.Get medical attention.
Eye contact:Irrigate with flowing water immediately and continuously for at least 15~20 minutes.Get medical attention.
Ingestion:Donot induce womition.get prompt medical attention.
Major Disease and Harm Effect::
First aid personal protection::
Prompt to Doctor:The manifestations of respiratory symptoms resulting from acute exposuer may be delayed.May cause respiratory sensitization No specific antidotes.Symptomatic and supportive care Treatment is based on judgement of the physician in response to reactions of the patient.

5、Fire Fightion Measuer

Suitable Extionuishing Media:Carbon dioxide,dry chemical,regular foam,or Water spray.
Fire and Extinguishing Media:Carbon dioxide,dry chemical,regular foam,or water spray.
Special extionguishing proceduer:Down-wind personnel must be evacuated,Keep up-wind,and avoid breathing hazardous vapors.Fight fire from a safe distance.Do not enter fire area without proper protection.
Special protection equipment:People fighting against polyol-based color paster must be protected by wearing positive perssure self-contained breathing apparatus and full positive clothing.

6、Accidental release measures

Personal protection:Isolate hazard area and keep unnecessary people away.Wear full protective equipment including respiratiory equipment during clean up.
Emvironmental protection:Evacuate and ventilate Dike spill to provent entry into water system.
Methods for cleaning up:Take up and place into containers for later disposal.Cover mops and brooms used for this with plastic and dispose properly (often by incineration).Landfill solids at permitted sites.

7、Handling and Storage

Handling :Observe all state and local regulations vhen handling with this substance.
Storage:Protect form atmospheric moisture,Keep container closed when not is use,and store in a cool,dry,and well-ventilated area.

8、Exposure control/personal protection

Engineering control:N/A
Control factor:N/A
Biotic Index:N/A
Personal Protection Equipent:
Respiratiory Protection:Not expected to present a respiratory hazard due to normally low vapor pressure.Wher respiratory protection is required for certain oqerations,use an approved supplied-air respirator.For emergency and other conditions,use an approved positive pressure self-contained breathing apparatus.
Hand Protection:It depends on operation to use appropriate protective gloves.Use safecy glasses.When contact with this material is likely,chemical goggles are recommended because eye contact may cause pain even though it is unlikely to cause injury. Skin&Body Protection: Use protective clothing impervious to this material.Selection of specific items such as gloves ,boots , apron,or full-body suit will depend on operation.
Hygiene procedures :Emergency shower should be available in the vicinity of work place.Wash hands before eation and drinking.Use plenty of soap and water for shower after work.

9、Physical and Chemical Properties /characteristics

Appearance:Muddy Form:Muddy paste
color:white Odor:Characteristic mild
HP value:-N/A Boiling Point / Boiling Range:>200.C
Decomposition Temperatuer:-N/A Flash point:>150.C
Test Method:
Spontaneous temperature:N/A Explosion Limits:N/A
Vapor pressue:-N/A Vapor density:-N/A
Specific gravity:N/A Solubility in water:Insoluble,reacts

10、Stability and Reactivity

Stability:Stable under recommended storage conditions
Special Conditions of Hazardous Reaction :Avoid water as it reacts to form heat and CO2.The combinse effect of the CO2 and heat can produce enough pressure to rupture aclosed container.
Conditions to Avoid:Heat sparks,open flame,and humidity,Heation in the presence of air (Oxygen) to temperature above 100.C may result in the formation of aldehydes.
Incompatibility:Water and oxidizers (string fire and explosion hazard).
Hazardous Decomposition Products : Toxic Oxides of carbon and Nitrogen.

11.Toxicological Information

Acute Toxicity:-N/A
Local effects :-N/A
Sensitive:Allergic or respiratory sensitization is possible , but only rarely.
Repeated exposures are not anticipated to cause any additional significant adverse effects.
Exceptional effect:-N/A

12.Ecological Information

Possibility of Environmental Impact/Move:N/A

13、Disposal Information

Disposal Information:Follow all state and local regulations.Liquids are usually incinerated in a proper facility.Solids are usually also incinerated or landfilled.Empty drums should be filled wity water .Let drum stand unsealed for 48hours .Before diposal drums shoule be drained,triple rinsed,and holed to prevent re-use.Dispose of drain and rinsefluid according to state and local laws and regulations.The most commonly accepted method is in an approved wastewater treatment facility Drums should be disposed of in accordance with state and local laws and regulations.commonly accepted method for disposal of plastic drums is disposal in and approved industrial incinerator or other appropriate incinerator facility.Steel drums are commonly disposed in and approved landfill after crushing or in accordance with other approved procedures

14.Transport Information

International Transport Regulation:-N/A
The United Nations number(Un0-No):N/A
Internal Transport Regulation:-N/A
Special transport way and Note:-N/A

15、Regulation Information

Apply regulation:N/A

16、Other Information
Reference